
All of Slovakia
Work at height: film application from aerial platforms
Large glazed areas are often high up. We fit film on façades, atriums, skylights and glass roofs from aerial platforms. We plan the work and safety the way large, demanding sites require.
- Façades, atriums, skylights
- Interior and exterior
- Work while the building stays open
- Certified for work at height
In short
Work at height means fitting film on glass you can’t reach from a ladder. That means façades, atriums, skylights and roofs. We work from aerial platforms and take care of safety. All our installers are certified for work at height and for operating aerial work platforms and walkways. We plan the schedule so the building can keep running. We have experience at shopping centres and nuclear power plants.
What window film does for you
-
Less heat in the room
Depending on film and glass, it stops 36 to 85 % of solar energy. Homes and offices stay cooler in summer.
-
Less glare
You can see your screen and TV even in the sun. No need to keep the blinds down all day.
-
UV protection
The film stops up to 99 % of UV radiation. Floors, furniture and shop-window goods fade much more slowly.
-
No new windows needed
We apply film to your existing glass. A flat or house usually takes one day, with no dust or building work.

Where we work at height
- Glazed façades of office buildings.
- Atriums and skylights in shopping centres.
- Halls, production and technical buildings.
- Universities, schools and public buildings.
- Glass roofs and polycarbonate canopies.
Film at height does the same job as on a window in a flat. It stops heat, glare and UV or holds broken glass together. The difference is organisation. On an ordinary window, skill is what counts. At height, preparation, equipment and safety matter just as much.
Which buildings
From platforms we mainly work on shopping-centre atriums and skylights. Also glazed façades of office buildings, halls and public buildings such as schools, hospitals and public offices.
At height we fit the same films as anywhere else. These are solar control, safety and polycarbonate films.
For family homes and conservatories, scaffolding or a ladder is usually enough.
Experience on demanding sites
We have worked at height where mistakes are not an option. At the Jaslovské Bohunice and Mochovce nuclear power plants we fitted solar films on large glazed areas. Access was by permit only, with personnel vetting. We went through safety training. The operator’s rules governed every step.
We also worked in the Aupark centres in Bratislava, Žilina and Košice. Also in Eurovea, Polus City Center and Galéria Prievidza. There we worked above atriums full of people. In sections, with fenced-off safety zones.
On Comenius University buildings we fitted the work around teaching.
Site visit and measuring at height
At the site visit we answer three questions. What is the glass? How do we reach it safely? When can we work?
We identify the glazing on each façade and the pane sizes. We assess the risk of thermal stress (glass cracking from uneven heating). This decides between inside and outside film.
Then we assess access. We check height and reach, obstacles under the glass and the load capacity of the floor or ground. We measure the entrances the platform must pass through. We check whether there is an underground car park beneath the atrium.
Pane sizes we can’t measure from the ground are checked from a platform or drawings. We verify them again before preparing the cutting plan.
Which platforms we use
- Scissor lifts. For level, firm floors, typically in atriums and halls. They have a large basket. The fitter can work comfortably with the full width of the film.
- Articulated and telescopic booms. For reaching over obstacles. For example kiosks in an atrium or planting in front of a façade.
- Truck-mounted platforms. For façades from the street or car park. They move quickly between sections.
- Tracked (spider) lifts. They fit through narrow doors and cross soft ground. They put little pressure on the floor.
Indoors we use electric platforms with non-marking tyres. We provide the platform and its operator as part of the job. If a platform can’t reach the glass, we arrange other access, such as scaffolding.
Safety and organisation
Before work starts we agree work sections, access routes and closures with the building manager. We also agree when work is allowed. For work on public land, we advise you on the occupation permit.
Under the platform we fence off a safety zone. Nobody may enter it. Tools in the basket are secured against falling.
Fitters are clipped in inside the basket. All are certified for work at height and for operating aerial work platforms and walkways. On high-security sites such as nuclear power plants, we follow all the operator’s rules.

Fitting at height step by step
- Section handover. The building manager releases a section. We fence it off and bring in the platform.
- Cleaning the glass. High glass is often dirtier: dust, cobwebs, sealant residue. We clean thoroughly, because any dirt under the film stays there.
- Application. We take the film up pre-cut to the plan. We apply it wet and squeegee the water out. We always work as a pair; on large panes both work together.
- Checking and tidying. We check every pane. We wipe water off frames and floor and hand the section back.
We don’t fit film outside in rain, frost or strong wind. Wind carries dust and affects the platform’s stability. The platform maker sets a maximum permitted wind speed. So we plan reserve days for outside work.
Curing and care of high glazing
At height too, water under the film evaporates gradually. With standard films this usually takes up to 30 days. In winter and with thick safety films it takes longer.
Tell your window-cleaning contractor. The film must not be cleaned for the first 30 days. After that, only with a cleaner with a pH of 6–8 (mild and neutral). No ammonia, razor blades or abrasive pads. With exterior films the same applies to façade cleaning.
What affects the price
- Platform hire. Charged per day. Delivery of the equipment to site is added.
- Lower output. At ground level our two installers fit about 30 m² a day. At height and on roofs it is less.
- Outside work. The film costs more and the work depends on the weather.
- Weekend work as the building requires. We work at night only when there is no other way, and for a surcharge.
- Occupation of public land, if needed.
- Travel at €0.45 per km actually driven, there and back, at least €30, incl. VAT. For sites more than 150 km from Bratislava, crew accommodation too.
So it pays to plan for the platform to spend as few days on site as possible. For example, combine several façades or atriums into one phase.
When film at height won’t help
Film won’t fix misted double-glazed units with failed seals. Nor leaking skylights or yellowed, brittle polycarbonate. Those need repair or replacement first.
Will the glass be replaced in a façade renovation in a few years? We will tell you whether the investment makes sense. On some triple glazing and large panes we won’t recommend inside film at all. The reason is thermal stress.
Preparing for the installation
Film is applied wet, so the fitter needs to reach the glass from the front and the sides with a squeegee, knife and sprayer.
Caring for window film
Do not clean the film for the first 30 days. A light haze and small water bubbles are normal. They disappear on their own as the film dries. In winter this takes longer.
Do
- Plenty of water with a drop of mild detergent (no ammonia)
- Soft microfibre cloth
- Rubber squeegee for the remaining water
- Clean exterior film just as gently as interior film
Don’t
- Razor blades, scrapers and rough sponges
- Cleaners with ammonia or grit
- Stickers, tape and suction cups on the film
- A pressure washer close to the edges of exterior film
Tip from practice: When you clean the frames, take care of the film edges. Do not lift them with a fingernail or cloth.
Full film care guideWhere we have worked
We have worked inside the Jaslovské Bohunice and Mochovce nuclear power plants. That meant security clearance and the strictest health and safety rules. We fitted film in open shopping centres in sections and from platforms. In Comenius University buildings we worked while teaching went on.
-
-
-
-
-
- Comenius University
- Polus City Center
- Galéria Prievidza
Why choose us to fit your film
We are a certified 3M Endorsed Installer. Our fitters were trained and tested by 3M itself. We have been fitting window and car films for 25 years. How long a film lasts depends on how well it is fitted.
We have even worked inside nuclear power plants
We fitted film at the Jaslovské Bohunice and Mochovce nuclear power plants. With security clearance, work permits and the strictest health and safety rules. We bring the same discipline to your flat or office.
Open shopping centres and work from platforms
Aupark, Eurovea and Polus did not close for us. We worked section by section and before opening. The work area was fenced off. We reached atriums and skylights from platforms. All our installers are certified for work at height and for operating aerial work platforms and walkways.
Only premium materials, data shown openly
We use only premium films from 3M, Avery Dennison, ORAFOL and Solar Screen. They last longer, keep their colour and carry a manufacturer warranty. For every film you get the data sheet and certificates. The values in our quote are the manufacturer’s figures to recognised standards. Not sales promises.
We tell you when film isn’t the answer
Sometimes film will not solve the problem. Or the glass could crack from uneven heat (thermal stress). Then we tell you plainly and suggest what to do instead.
How it works
From your first message to the finished job usually takes a few days. For buildings, we plan the work so it does not disrupt your operations.
Enquiry or photo
Fill in the online form and see an estimated price at the end. Or send a photo to m2s@m2s.sk. Rough sizes are enough.
Free site visit
For buildings, we visit, measure the windows and check the glass. Then we recommend a suitable film.
Your quote
We prepare it as soon as possible. It has a clear price, the exact material, a date and the warranty terms.
Installation and warranty
Our team of two installers fits the film. You get the data sheet, the manufacturer’s warranty terms and an invoice. For cars, also a certificate of installation.
Frequently asked questions
Didn’t find your answer? E-mail us or send a free quote request – advice costs nothing.
Send us an e-mailHow high can you work?
We choose the height and type of platform to suit the building. Send us photos and the rough height. We will propose a suitable solution.
Do you provide the platform yourselves?
Yes. We provide the platform and its operator as part of the job, including delivery to site.
Who arranges the occupation of public land?
The municipality or city district grants the permit. We help with the documents and dates. By agreement we can arrange it for you.
Can you work while the building is open?
Yes. We work in sections and fence off the work area. Where needed, we work outside opening hours. We work at night only when there is no other way, and for a surcharge.
Do you apply film at height from inside and outside?
Yes. We choose inside or outside film by glass type and access. With insulating glass and large panes, the risk of thermal stress also decides.
Will the atrium floor take a platform?
We check this in advance with the building manager. If there is a car park or weaker floor beneath, we have options. We use a lighter platform, load-spreading pads or work from another side.
Do you work on high-security sites?
Yes. We have worked at the Jaslovské Bohunice and Mochovce nuclear power plants. Strict rules apply there to access, work permits and health and safety. We will adapt to your site’s rules too.
What if it rains or is windy during the work?
We don’t work outside in rain, frost or strong wind. So the schedule includes reserve days. That way we keep the deadline.
Who cleans the glass with film afterwards?
Your cleaning or high-access contractor, following our instructions. Nothing for the first 30 days. Then a cleaner with a pH of 6–8, without ammonia, razor blades or abrasive pads.
Will you prepare documentation for the building manager and health and safety?
Yes. We prepare the film data sheet and the method statement. We also supply the documents the building manager or safety coordinator needs.
How quickly can you prepare a quote?
Send photos, the rough height and the glass area to m2s@m2s.sk or via the form. We will reply as soon as possible. We will arrange a free site visit.
What do I need to prepare before the film is applied?
Clear access to the windows: leave roughly 1 metre of free space in front of and beside every window. Move wardrobes, beds, desks and plants away beforehand, clear the window sills, pull curtains aside and raise interior blinds. If something heavy cannot be moved, tell us in advance and we will plan around it.
Related services
-
Shopping centres and retail
Atriums, skylights and shop windows: less heat and UV, more security. Work outside opening hours.
Learn more -
Offices
A cooler open-plan office, screens without glare and glass partitions with privacy.
Learn more -
Businesses and public buildings
Schools, hospitals, public offices, hotels, industry and energy.
Learn more

Send us a photo of your window or car. We’ll prepare a quote as soon as possible.
A few details and a phone photo are enough. We’ll e-mail you a quote as soon as possible.