3Mfolie.skWindow & car films
Woman cleaning a window with a soft microfibre cloth

All of Slovakia

Window and car film care

Good film needs very little care. But that care has to be right. Film is rarely damaged by age. It is damaged by the wrong cleaner, a scraper or a suction cup. Here are the rules for every film we install, on windows and on cars.

  • Rules for windows and cars
  • What is normal after installation
  • When to contact us

In short

Don’t clean window film for the first 30 days. Don’t wash a car with new film for the first few days; we tell you the exact date at handover. Until then, haze and small water bubbles are normal. After that, use plenty of water, a mild ammonia-free cleaner and a soft cloth. Never use razor blades, scrapers, rough sponges or suction cups. Never scrub film edges or aim a pressure washer at them from close up.

Materials we install
Water droplets and haze on glass

The first weeks: haze and bubbles are normal

Haze and small water bubbles after installation are not a defect. We apply film wet. A thin layer of mounting solution stays between the film and the glass. The water then slowly evaporates through the film.

We call this curing (the adhesive bonds fully as it dries). Until the film has cured, it needs nothing. Just leave it alone.

  • Thin window films up to about 100 µm (0.1 mm) cure in around 30 days.
  • Mirror films dry more slowly. The haze can stay for several weeks.
  • Thick safety films take the longest. The haze can stay for several months, around 140 days for the thickest.
  • Car films need a few quiet days. We tell you the exact date of the first wash at handover.

Curing takes longer in cold weather and on windows without sun. Don’t press the bubbles or push them out. We judge the result only once the film has fully dried.

What to clean every film with

  • Plenty of clean water. Soak and rinse dirt off; don’t scrub it.
  • A mild, ammonia-free cleaner. A drop of washing-up liquid is enough. A pH of 6 to 8 is ideal (not acidic or strongly alkaline).
  • A soft microfibre cloth. Always clean and free of grit.
  • A rubber squeegee. The blade must be clean and undamaged.
  • For cars, a pH-neutral shampoo. Hand washing is best.

Cleaning a window is simple. Rinse the glass first. Then spray on the solution and wash gently. Squeegee the water off.

Don’t press hard or keep scrubbing one spot. Use a separate cloth for frames and sills.

Man cleaning a glazed door with a spray and a cloth

What never to use

  • Ammonia. Some ordinary window cleaners contain it. Check the label.
  • Razor blades, scrapers and knives. Not even for a sticker or dried paint.
  • Rough sponges, brushes and polishing pastes. No gritty scouring powders either.
  • Solvents. For example acetone or thinners.
  • Steam cleaners.
  • Tape, stickers, suction cups and hooks. They damage the film surface when removed.
  • Coarse paper towels and newspaper.
  • Dirty water from frames or outside windows. The grit in it scratches the film.

A scratch in film cannot be polished out. Prevention is cheaper than repair.

Solar film on the inside of the glass

You clean interior solar film almost like a normal window. This includes the interior version of 3M Prestige. It also includes other heat-control films on the inside of the glass.

Water, a drop of mild ammonia-free cleaner and a soft cloth are enough. Remove the rest of the water with a rubber squeegee.

Wash windows with solar film at least once a year. Built-up dirt reduces how well the film works.

Take care of the film edges when you clean the frames. Don’t lift them with a fingernail or a cloth. Read more on solar window film.

Modern office building with a fully glazed facade

Exterior film on the outside

Clean exterior film as gently as interior film, but more often. It is outside, so dust, rain and bird droppings settle on it.

First rinse off loose dirt with clean water. Then wash it with a mild solution and a soft cloth. Finally, rinse again. Never clean it dry.

  • Avery Dennison recommends cleaning exterior films at least three times a year. In dusty areas, clean them more often.
  • Don’t aim a pressure washer at the film edges from close up.
  • Don’t scrape ice off the film. Let it melt.
  • On sloped and horizontal glass, the film edges are sealed. Check the sealant once a year, especially after winter.

Following the care instructions is a condition of the manufacturer’s warranty. We explain both film types on interior vs. exterior film. On roof windows and skylights, checking the sealant matters even more.

Mirror and reflective films

Always wet mirror film before you wipe it. It has a metal layer, and scratches show more than on clear film.

It dries more slowly than clear film. The haze can stay for several weeks.

Clean it in the shade or at dusk. In the sun, water dries fast and leaves streaks. Pull the squeegee in one direction.

Never dust it dry. That leaves fine scratches.

Wash windows with mirror film twice a year. Under a layer of dirt, metallic film heats up more. Read more on reflective and mirror films.

Safety films under the glazing bead

Safety film mainly needs time and intact edges. It is thick, so it dries the longest. Haze and bubbles can stay for several months. Don’t clean it for the first 30 days.

After that, clean it with water and a mild ammonia-free cleaner. Use a soft cloth and a rubber squeegee.

On PVC and aluminium windows we fit the film right under the glazing bead. This is part of the protection. If the glass breaks, the bead holds the filmed glass in the frame.

Check the film edges and the beads once a year. Never drill or screw anything through the film. Don’t remove the sealant or beads at the edges.

Planning to replace window beads or seals? Contact us first. Read more on security window film.

Decorative, frosted and printed films

Wipe frosted film more often, but always gently. A matte surface holds grease from fingers, especially on glass doors.

Wipe fingerprints off with a damp soft cloth. Water with mild soap is enough. Wipe printed film without pressure.

Don’t use thinners or alcohol cleaners on printed film. Don’t put tape or stickers on it.

Frosted film may look uneven for the first few days. It evens out once dry. See the range on decorative glass film.

Anti-graffiti films

Remove tags and marker from anti-graffiti film as soon as possible. The longer they stay, the harder they are to remove.

A normal ammonia-free glass cleaner and a soft cloth are enough. For the first 30 days, clean the film only when you must. The adhesive is still bonding.

Don’t use razor blades, scrapers or polishing pastes on tags or scratches. Use aggressive solvents only after asking us.

The film is a sacrificial layer (it takes the damage instead of the glass). If someone scratches or etches it, we replace only the film. The glass stays intact. Read more on anti-graffiti film.

Film on polycarbonate and acrylic

Clean film on plastic only with lukewarm water and mild soap. Polycarbonate and acrylic are more delicate than glass.

Rinse off dust first. Only then wipe with a soft microfibre cloth. Never wipe it dry.

Don’t use alcohol, acetone or solvent cleaners. They damage polycarbonate and acrylic. Watch out for ordinary window cleaners with alcohol too.

Unsure about a cleaner? Test it on a small corner first. Read more on polycarbonate film.

Hand-washing a car side window with a sponge

Tinted car windows

For the first few days after tinting, don’t lower the side windows. Don’t clean the glass from inside. The film has to dry. We tell you the exact number of days at handover; it depends on the weather.

Let haze and small bubbles dry. Don’t press them.

  • Clean the inside with a soft microfibre cloth and an ammonia-free cleaner.
  • On the rear window, wipe along the heater lines.
  • Don’t put suction cups, such as a phone holder, or stickers on the film.
  • Watch seat belts, buckles and luggage. A sharp edge scratches the film from inside.
  • Scrape ice off the outside as usual. The film is on the inside. Never put a scraper or sharp object on the inner side of the glass.

The tinting rules are on window tinting.

Hand-washing a car with a sponge and foam

PPF: paint protection film

Hand wash a car with PPF (clear film that protects the paint). Use a pH-neutral shampoo. Don’t wash the car for the first few days after application. We tell you the date of the first wash at handover.

Remove insects and bird droppings as soon as possible. Light swirl marks in the film disappear with heat. Sun or warm water will do.

Don’t aim a pressure washer at film edges and seams from close up. Keep the nozzle pointed away from them. Skip brush car washes right after application.

A ceramic coating can go on top of PPF. See the comparison on PPF vs. ceramic coating.

  • Gloss PPF: the rules above are enough.
  • Matte PPF: no wax, as it leaves glossy patches. No polishing compounds or machine polishing.
  • Matte PPF: use products made for matte finishes.

Read more on paint protection film.

Car wrapped in matte grey film, headlight detail

Car wrap, graphics and chrome delete

Hand wash a wrapped car, ideally with the two-bucket method. One bucket holds shampoo, the other rinse water for the mitt. That way dirt doesn’t go back onto the film.

Don’t wash the car for the first few days after wrapping. The film is still settling at edges and in recesses. We tell you the date of the first wash at handover.

The same rules apply to vehicle graphics and chrome delete (covering chrome trim with film).

  • Wipe off spilled fuel and bird droppings at once.
  • No wax or polish on matte or satin film. Use products made for matte finishes.
  • Avoid brush car washes. They wear the surface faster.
  • Don’t aim a pressure washer at edges and seams from close up.
  • Never scrape ice directly off the film.
  • Park in the shade when you can.

Read more on car wrap, vehicle graphics and chrome delete.

Cars in a service workshop

When to contact us

Contact us when a film edge starts to lift. The sooner, the better. Dirt and water get under a lifted edge.

  • A lifted corner or edge. Don’t press it down or tape it.
  • Bubbles or haze after full curing. Send us a photo.
  • Damaged film. For example a scratch, a tear or a stone chip in PPF.
  • Cracked sealant at the edge. This concerns exterior films and roof windows. We renew the sealant.
  • Replacing beads or seals. With safety film under the bead, contact us before the work.
  • Cracked glass. Send a photo of the crack. We assess the cause; see thermal stress in glass.

Send photos to m2s@m2s.sk or via the form. We reply as soon as possible. The claims process is in our complaints procedure.

Office building with ribbon windows on every floor

Lifespan and replacing old film

The right care makes film last longer. Lifespan is shortened mainly by wrong cleaning and physical damage.

Interior window films typically last 10 to 15 years or more. Exterior 3M Prestige lasts 10 to 15 years. The manufacturer’s warranty depends on the film type and the position of the glass. We state it in the quote.

Details for each film type are on film lifespan.

At the end of its life, film loses performance. It may change colour or peel. We remove old film with the adhesive residue, without damaging the glass. See how on old film removal. We don’t recommend doing it yourself with a razor blade.

Film care at a glance

FilmFirst washClean withNever use
Interior solar film (e.g. 3M Prestige)After 30 days.Water, a drop of detergent, microfibre, squeegee.Ammonia, razor blades, rough sponges.
Exterior filmAfter 30 days.Rinse first, then mild solution and a soft cloth.Dry wiping, pressure on edges, scraping ice.
Mirror (reflective) filmAfter 30 days; haze may last longer.Plenty of water, microfibre, clean in the shade.Dry dusting, ammonia.
Safety film (incl. under the bead)After 30 days; haze may last months.Mild ammonia-free solution, squeegee.Drilling, removing sealant or beads.
Decorative and frosted filmAfter 30 days.Damp soft cloth, mild soap.Thinners and alcohol on printed film.
Anti-graffiti filmAfter 30 days, unless needed sooner.Ammonia-free glass cleaner.Razor blades, polishing pastes, solvents without asking.
Film on polycarbonateAfter 30 days.Lukewarm water and mild soap.Alcohol, acetone, solvents.
Car window tintAfter the first few days; date given at handover.Microfibre and ammonia-free cleaner.Scrapers inside, suction cups, ammonia.
Gloss PPFAfter the first few days; date given at handover.Hand wash, pH-neutral shampoo.Pressure washer close to edges.
Matte PPFAfter the first few days; date given at handover.Hand wash, products for matte finishes.Wax, polishing compounds, machine polishing.
Car wrap, graphics, chrome deleteAfter the first few days; date given at handover.Hand wash, two-bucket method.Brush car washes, wax on matte film, ice scrapers.

The instructions follow recommendations from 3M, Avery Dennison and the 3M distributor in Slovakia. Curing time depends on film thickness, temperature and window direction.

Updated: November 2026

Why choose us to fit your film

We are a certified 3M Endorsed Installer. Our fitters were trained and tested by 3M itself. We have been fitting window and car films for 25 years. How long a film lasts depends on how well it is fitted.

  • We have even worked inside nuclear power plants

    We fitted film at the Jaslovské Bohunice and Mochovce nuclear power plants. With security clearance, work permits and the strictest health and safety rules. We bring the same discipline to your flat or office.

  • Open shopping centres and work from platforms

    Aupark, Eurovea and Polus did not close for us. We worked section by section and before opening. The work area was fenced off. We reached atriums and skylights from platforms. All our installers are certified for work at height and for operating aerial work platforms and walkways.

  • Only premium materials, data shown openly

    We use only premium films from 3M, Avery Dennison, ORAFOL and Solar Screen. They last longer, keep their colour and carry a manufacturer warranty. For every film you get the data sheet and certificates. The values in our quote are the manufacturer’s figures to recognised standards. Not sales promises.

  • We tell you when film isn’t the answer

    Sometimes film will not solve the problem. Or the glass could crack from uneven heat (thermal stress). Then we tell you plainly and suggest what to do instead.

How it works

From your first message to the finished job usually takes a few days. For buildings, we plan the work so it does not disrupt your operations.

  1. Enquiry or photo

    Fill in the online form and see an estimated price at the end. Or send a photo to m2s@m2s.sk. Rough sizes are enough.

  2. Free site visit

    For buildings, we visit, measure the windows and check the glass. Then we recommend a suitable film.

  3. Your quote

    We prepare it as soon as possible. It has a clear price, the exact material, a date and the warranty terms.

  4. Installation and warranty

    Our team of two installers fits the film. You get the data sheet, the manufacturer’s warranty terms and an invoice. For cars, also a certificate of installation.

Frequently asked questions

Didn’t find your answer? E-mail us or send a free quote request – advice costs nothing.

Send us an e-mail
Why are there bubbles under my new film?

Small water bubbles are normal for the first weeks. They are left-over mounting solution and evaporate on their own. Don’t press them. If they remain after full curing, send a photo to m2s@m2s.sk.

Why does my window film look hazy after installation?

Water from the installation is still drying under the film. Thin films cure in about 30 days. Thick safety films can take several months. It takes longer in cold weather.

When can I first clean a window with film?

After 30 days at the earliest. With thick safety film, we tell you whether to wait longer. Until then, don’t press on the film.

Can I use a window cleaner with ammonia?

No. Ammonia damages the film. Some ordinary cleaners contain it, so check the label. Water with a drop of mild washing-up liquid is enough.

Can I clean film with a steam cleaner?

No. A steam cleaner should not touch film, on windows or on cars. Use water, a mild cleaner and a soft cloth.

Can I put a suction cup on the film?

No. Don’t put suction cups, hooks, tape or stickers on film. They damage the surface when removed. This includes phone holders on tinted glass.

Can I use a pressure washer on a car with PPF or a wrap?

Yes, but not close up on film edges and seams. Keep the nozzle pointed away from the edges. Don’t wash the car at all for the first few days.

Can I wax matte PPF?

No. Wax leaves glossy patches on matte film. Don’t use polishing compounds or machine polishing either. Use products made for matte finishes.

Can I take a car with PPF or a wrap through a brush car wash?

Not right after application. With a wrap, avoid brush car washes altogether, as they wear the surface faster. Hand washing is always best for film.

When can I lower my windows after tinting?

Only after the first few days, once the film has dried. We tell you the exact number of days at handover. It depends on the weather.

Can I scrape ice off windows with film?

On tinted car windows, yes, because the film is on the inside. Never put a scraper on the inner side of the glass. Don’t scrape ice off exterior window film or a wrap; let it melt.

What should I do if a film edge is lifting?

Don’t press it down or tape it. Send us a photo to m2s@m2s.sk or via the form. The sooner we fix it, the less dirt gets under the film.

Gloved hands stretching blue film over a car body

Send us a photo of your window or car. We’ll prepare a quote as soon as possible.

A few details and a phone photo are enough. We’ll e-mail you a quote as soon as possible.

  1. 1Service
  2. 2Details
  3. 3Photos
  4. 4Price

What do you need?

The more you tell us, the more accurate the quote. You will see an estimated price at the end.

Job type

Which car is it?

The model and scope let us price precisely – we have film patterns for most cars.

Car

Services

Choose any.

Window tinting

Which windows to tint

Front side windows: clear 3M Safety film only. Windscreen: sun strip only. Choose both in the services above. Pick windows on the 3D model

PPF paint protection film

Coverage

Pick exact panels on the 3D car model.

Film

The estimate below is for gloss PPF. We state the price difference between GSWF, Avery Dennison and HOHO in the quote.

Finish

Film type

Tell us about the windows

Approximate details are enough. We measure precisely during the free site visit.

What do you want to solve?

Choose any.

Film type

Price of the film alone, incl. VAT. Application is added.

Glass sizes

How to measure the glass

Film is applied to the glass only, never to the frame. Measure just the visible glass – from bead to bead.

glass width glass height frame don’t measure bead measure from here
  1. Measure the width and height of the visible glass from one glazing bead to the opposite bead. Do not measure the frame or the sash.
  2. Measure each pane separately. If the window has glazing bars, measure each section and enter how many identical pieces there are.
  3. Centimetre accuracy is enough – round up. We cut the film to size on site anyway.
  4. Not sure? Send a photo of the window with a tape measure, or book a free site visit.

Measure the glass only, bead to bead – not the frame. Enter identical panes once with a quantity.

WidthHeightQtyRemove
cm cm
m²
Film applied

Glass and windows

Glass type
Window frame type

With wooden windows the application costs 20 % more.

Window orientation (choose any)
Access to the windows

Where is the job?

We work out travel from Bratislava from the town.

km

Extras

We need clear access to the windows – at least 1 metre. Please leave roughly 1 m of free space in front of and beside every window. Wardrobes, beds, desks or plants must be moved away before the film is applied, curtains pulled aside and interior blinds raised. The fitters can then work faster and cleaner, with no risk to your furniture.

Photos and notes

A phone photo is often enough for an accurate quote without a visit. Photograph the whole window and its surroundings; for cars the full side and front.

Photos

Site visit

Estimated price

–

    This is an estimate based on your details. We confirm the exact price after a visit or from photos – we will get back to you as soon as possible.

    Where should we send the quote?

    Contact

    How should we contact you?

    Company

    Optional. Fill in if the quote is for a company.

    Search