
All of Slovakia
Spectrally selective window film: light in, heat out
Want less heat but not a dark room? That is what spectrally selective films are for. They let in plenty of light and stop mainly heat. We explain how it works and how to check it in the numbers.
- Explained without jargon
- Manufacturer values
- Compared with metallic films
In short
Spectrally selective film lets through more light than heat. It mainly stops invisible infrared radiation, which carries a large share of the heat. Visible light gets through. Selectivity is shown by the LSG number (light divided by the solar factor g). If LSG is above 1, the film is selective. 3M Prestige 70 Exterior has an LSG of about 1.6 on double glazing. A strong mirror film has an LSG below 1 on single glazing. It stops a lot of heat, but most of the light too.
What window film does for you
-
Less heat in the room
Depending on film and glass, it stops 36 to 85 % of solar energy. Homes and offices stay cooler in summer.
-
Less glare
You can see your screen and TV even in the sun. No need to keep the blinds down all day.
-
UV protection
The film stops up to 99 % of UV radiation. Floors, furniture and shop-window goods fade much more slowly.
-
No new windows needed
We apply film to your existing glass. A flat or house usually takes one day, with no dust or building work.

What spectrally selective film is
Sunlight has three parts. About 3 % is UV and 44 % is visible light. The remaining 53 % is infrared radiation (invisible heat).
An ordinary dark film blocks everything evenly. With it, less heat also means less light.
Spectrally selective film tells them apart. It lets visible light in. It stops much of the infrared and UV. It works like a filter that picks and chooses.
How to spot it in the numbers
- VLT (visible light transmission) – the share of visible light that reaches the room.
- g-value (solar factor) – the share of solar energy that gets inside. Lower is better.
- TSER (total solar energy rejected) – how much energy the film stops. TSER = 1 − g.
- LSG (selectivity) – VLT divided by g. Above 1 means more light than heat gets through.
Example: 3M Prestige 70 Exterior on single glazing lets through 71 % of light. Its solar factor is 0.48. So LSG is 0.71 / 0.48, or about 1.48.
A higher LSG means a brighter room for the same heat reduction. Always compare values on the same type of glass.
Metallic vs. metal-free film
The older way to stop heat is a thin metal layer. It works like a mirror and reflects light and heat.
Metallic films are effective and cheaper. But they reflect strongly and look like mirrors in daytime. They can also weaken mobile signal. More on reflective and mirror films.
3M Prestige has no metal. It is made of more than 200 nano-layers. Its reflection is only 5 to 9 %. It doesn’t affect mobile signal, 5G or Wi-Fi.

When selective film is worth it
- You want a bright room – living rooms, offices and classrooms where people work by daylight.
- You don’t want a mirror – blocks of flats, historic buildings, shop windows.
- You need signal – offices, hotels and homes with Wi-Fi.
- You have houseplants – a light selective film leaves them most of the light. See window film and houseplants.
Selective film isn’t always the best choice. For daytime privacy, reflective film helps more. To stop as much heat as possible regardless of light, consider a darker film.
Selective films we fit
- 3M Prestige Exterior – grades 90, 70, 50, 40 and 20. Fitted outside, also suits double and triple glazing.
- 3M Prestige Interior – grades 70 and 40. Fitted inside, mainly on single glazing and smaller double-glazed units.
- Avery Dennison SP e-Lite 70X – an exterior selective film. According to the manufacturer it lets through about 61 % of light and rejects about 61 % of solar energy.
The full range is on 3M Prestige. Choosing by glass type is explained on interior vs. exterior film.
What you measure and what you see
A film with 63 % VLT doesn’t make a room a third darker. The eye perceives a drop in light as smaller than the measurement shows.
So Prestige looks brighter than its VLT suggests. We explain this in detail on 3M Prestige technical data.
The best test is a sample on your own window. At the site visit we hold it right against your glass.
Selective film in winter
Solar film also stops part of the sun’s heat in winter. On sunny winter days slightly less solar heat gets in.
Solar film doesn’t change heat loss through the window, the U-value.
How Prestige behaves through the year is explained on 3M Prestige in summer and winter.
Film selectivity on single glazing
| Film | Light (VLT) | Solar factor g | LSG | Type |
|---|---|---|---|---|
| 3M Prestige 90 Exterior | 88 % | 0.64 | 1.38 | selective, almost invisible |
| 3M Prestige 70 Exterior | 71 % | 0.48 | 1.48 | selective |
| 3M Prestige 70 Interior | 69 % | 0.50 | 1.38 | selective |
| 3M Prestige 40 Exterior | 42 % | 0.39 | 1.08 | slightly selective, darker |
| 3M Neutral 70 Interior | 69 % | 0.68 | 1.01 | neutral, stops little heat |
| 3M Neutral 35 Exterior | 44 % | 0.49 | 0.90 | dark, not selective |
| 3M Silver 35 Exterior | 37 % | 0.36 | 1.03 | reflective (mirror) |
| 3M Silver 15 Exterior | 17 % | 0.19 | 0.89 | strong mirror |
3M manufacturer data (EN 410 / NFRC), 6 mm clear glass. We calculated LSG as VLT / g. Values differ on double glazing. For example, Prestige 70 Exterior has an LSG of about 1.6 on double glazing.
Preparing for the installation
Film is applied wet, so the fitter needs to reach the glass from the front and the sides with a squeegee, knife and sprayer.
Caring for window film
Do not clean the film for the first 30 days. A light haze and small water bubbles are normal. They disappear on their own as the film dries. In winter this takes longer.
Do
- Plenty of water with a drop of mild detergent (no ammonia)
- Soft microfibre cloth
- Rubber squeegee for the remaining water
- Clean exterior film just as gently as interior film
Don’t
- Razor blades, scrapers and rough sponges
- Cleaners with ammonia or grit
- Stickers, tape and suction cups on the film
- A pressure washer close to the edges of exterior film
Tip from practice: When you clean the frames, take care of the film edges. Do not lift them with a fingernail or cloth.
Full film care guideUpdated: November 2026
Why choose us to fit your film
We are a certified 3M Endorsed Installer. Our fitters were trained and tested by 3M itself. We have been fitting window and car films for 25 years. How long a film lasts depends on how well it is fitted.
We have even worked inside nuclear power plants
We fitted film at the Jaslovské Bohunice and Mochovce nuclear power plants. With security clearance, work permits and the strictest health and safety rules. We bring the same discipline to your flat or office.
Open shopping centres and work from platforms
Aupark, Eurovea and Polus did not close for us. We worked section by section and before opening. The work area was fenced off. We reached atriums and skylights from platforms. All our installers are certified for work at height and for operating aerial work platforms and walkways.
Only premium materials, data shown openly
We use only premium films from 3M, Avery Dennison, ORAFOL and Solar Screen. They last longer, keep their colour and carry a manufacturer warranty. For every film you get the data sheet and certificates. The values in our quote are the manufacturer’s figures to recognised standards. Not sales promises.
We tell you when film isn’t the answer
Sometimes film will not solve the problem. Or the glass could crack from uneven heat (thermal stress). Then we tell you plainly and suggest what to do instead.
How it works
From your first message to the finished job usually takes a few days. For buildings, we plan the work so it does not disrupt your operations.
Enquiry or photo
Fill in the online form and see an estimated price at the end. Or send a photo to m2s@m2s.sk. Rough sizes are enough.
Free site visit
For buildings, we visit, measure the windows and check the glass. Then we recommend a suitable film.
Your quote
We prepare it as soon as possible. It has a clear price, the exact material, a date and the warranty terms.
Installation and warranty
Our team of two installers fits the film. You get the data sheet, the manufacturer’s warranty terms and an invoice. For cars, also a certificate of installation.
Frequently asked questions
Didn’t find your answer? E-mail us or send a free quote request – advice costs nothing.
Send us an e-mailWhat does spectrally selective film mean?
It is a film that lets through more light than heat. It mainly stops infrared and UV radiation. Visible light gets through.
How do I tell if a film is selective?
Divide its light transmission (VLT) by its solar factor g. If the result is above 1, the film is selective. Both values are in the data sheet.
Is 3M Prestige spectrally selective?
Yes. Prestige 70 Exterior has an LSG of about 1.48 on single glazing. On double glazing it is about 1.6.
What is the difference between selective and mirror film?
Mirror film has a metal layer and reflects both light and heat. It looks like a mirror in daytime and darkens the room. Selective film lets light in and stops mainly heat, without a mirror look.
Is selective film more expensive?
Usually yes. 3M Prestige fitted inside costs €120 to €160/m² incl. VAT. Mirror film costs €60 to €90/m². More on how much window film costs.
Will selective film darken the room?
Light grades only slightly. Prestige 70 lets through 63 % of light on double glazing. The eye sees it as a smaller drop.
Does selective film stop as much heat as mirror film?
A dark mirror film usually stops more heat. But it also blocks much more light. Selective film gives a better balance of light and heat.
Does selective film affect signal?
Metal-free selective films like 3M Prestige don’t block signal. Mobile, 5G and Wi-Fi work as before.
Does selective film help in winter?
Solar film doesn’t change heat loss through the window. In winter it also stops part of the sun’s heat.
Is selective film suitable for double glazing?
Yes, but we choose by the glass. For double and triple glazing we often recommend the exterior version. It heats the glass less.
Can you see from outside that there is film on the window?
With a light metal-free film, hardly. 3M Prestige reflects only 5 to 9 %. The window doesn’t look like a mirror.
Can I see the film first?
Yes. At the site visit we hold samples right against your glass. The site visit is free.
What do I need to prepare before the film is applied?
Clear access to the windows: leave roughly 1 metre of free space in front of and beside every window. Move wardrobes, beds, desks and plants away beforehand, clear the window sills, pull curtains aside and raise interior blinds. If something heavy cannot be moved, tell us in advance and we will plan around it.
Related services
-
3M Prestige – film without the mirror look
Less heat, the same view. Who it suits, which version to pick, what affects the price and how fitting works.
Learn more -
Reflective and mirror films
Daytime privacy and the strongest heat protection. Up to 85 % of solar energy on double glazing.
Learn more -
Solar control films
Less heat and glare in summer. 99.9 % UV protection, no mirror look.
Learn more

Send us a photo of your window or car. We’ll prepare a quote as soon as possible.
A few details and a phone photo are enough. We’ll e-mail you a quote as soon as possible.