3Mfolie.skWindow & car films
Sun beating down on the glass facade of a high-rise

All of Slovakia

Overheating offices and buildings: what to do

A glazed office soon turns into a greenhouse in summer. Staff complain and the air conditioning runs flat out. Here is an overview for building managers. What the regulation says, where the cause lies and what really helps.

  • Limits checked in Regulation 99/2016
  • Solutions for buildings in use
  • Fitting outside working hours

In short

An office overheats mainly from sunlight passing through the glass. For seated office work, the highest permitted temperature in the warm season is 28 °C. This is set by Slovak Ministry of Health Regulation No. 99/2016. Among the measures against heat stress, it lists shading of windows and rooflights. Solar film stops heat right at the glass. It needs no building work and is fitted while the building is in use. It won’t replace air conditioning, but it reduces its load.

Materials we install

What window film does for you

  • Less heat in the room

    Depending on film and glass, it stops 36 to 85 % of solar energy. Homes and offices stay cooler in summer.

  • Less glare

    You can see your screen and TV even in the sun. No need to keep the blinds down all day.

  • UV protection

    The film stops up to 99 % of UV radiation. Floors, furniture and shop-window goods fade much more slowly.

  • No new windows needed

    We apply film to your existing glass. A flat or house usually takes one day, with no dust or building work.

How much will you save on air conditioning? Enter your glass area and film. The calculator shows how much heat the film stops and what you save.
Laptop on a desk in harsh sunlight from the window

Why a building overheats

The main cause is sunlight passing through the windows. Solar energy is about 3 % UV. Some 44 % is visible light and 53 % is infrared radiation (invisible heat).

Inside the room, light turns into heat. That heat cannot easily get back out through the glass. That is how a greenhouse works.

Modern buildings have lots of glass and often little shading. Add the heat from computers, lighting and people.

South and west facades suffer most. Afternoon sun from the west is low and reaches deep into the room.

What the regulation says

Workplace temperature in Slovakia is covered by Ministry of Health Regulation No. 99/2016. It deals with protecting health from heat and cold at work. The key points for summer:

  • Warm season – days with an average daily outdoor temperature of 13 °C or more.
  • Office work (work class 1a, seated computer work) – the optimum is 23 to 27 °C. The highest permitted temperature is 28 °C.
  • Light manual work (class 1b, for example lab work) – optimum 22 to 25 °C, maximum 27 °C.
  • Direct sun – it should not shine on an employee’s head for more than 10 minutes per shift. This is managed by placing windows, blinds and workstations well.
  • Measures – the regulation names, for example, air conditioning, breaks, shifting working hours and shading of windows and rooflights.

The limits apply to operative temperature. That is the temperature the body feels from the air and from radiant surfaces around it. Near hot glass it is often higher than the air temperature on a thermometer.

Your health and safety adviser will confirm the exact duties for your site. We handle the technical side – the glass and the heat that passes through it.

Modern office building with a fully glazed facade

Which solution to choose

External shading stops the most heat. But on an existing building it is rarely quick or cheap to install.

Film is the quickest fix, right on the glass. Air conditioning treats the result. It removes heat only after it has got in.

A combination works best. Film reduces the load and air conditioning handles the rest. A comparison that also covers homes is on film vs. blinds and air conditioning.

What film changes in a building

  • Less solar heat – 3M Prestige 70 Exterior on double glazing rejects 61 % of solar energy. Prestige 40 Exterior rejects 71 % (manufacturer data).
  • Daylight stays – Prestige 70 lets through 63 % of light on double glazing. The office doesn’t feel dark.
  • Less glare – screens are easier to read and blinds can stay up.
  • UV protection – Prestige blocks 99.9 % of UV. It slows the fading of furniture and floors.
  • Signal stays – Prestige has no metal layer. It doesn’t affect mobile, 5G or Wi-Fi.

Film doesn’t stop heat from walls, the roof or equipment. So it won’t fully replace air conditioning. How much the temperature drops depends on orientation, glass area and shading.

Estimate the cooling saving in our energy-saving calculator.

Open-plan office with desks by the windows

What to consider in a building in use

  • Glass type – we check double and triple glazing and large panes for thermal stress. That is the risk of cracking from uneven heating. We often choose exterior film for this reason.
  • Access – at height we work from platforms or scaffolding. The team is always two fitters certified for work at height and for operating platforms.
  • Operation – we work room by room and floor by floor. By arrangement also in the evening, at weekends or outside opening hours.
  • Sample area – on larger sites we can fit a sample first. You see the light and look before you decide.
  • Documents – we supply data sheets, an invoice and documents for procurement.
  • Warranty – we are a 3M Endorsed Installer. We state the manufacturer’s warranty for the chosen film in the quote.

Experience on large sites

We have fitted solar film on large glazed areas for 25 years. We have worked in the Aupark shopping centres in Bratislava, Žilina and Košice. Also in Eurovea, Polus City Center and Galéria Prievidza.

We have also worked on Comenius University buildings while they were in use. And in the Jaslovské Bohunice and Mochovce nuclear power plants, with strict safety rules.

Our approach for companies and public bodies is on films for businesses and public buildings.

How to start

  • Send us a list of windows or a floor plan showing which way the facades face.
  • Add photos of the glass and the glazing type, if you know it.
  • At the site visit we measure the windows and assess the glass.
  • You get a quote with the film values and a work schedule.

Start with a free quote request or e-mail m2s@m2s.sk. The site visit is free.

Solutions from a building manager’s view

SolutionWhere it stops heatImpact on the buildingOperation and upkeep
Solar filmAt the glass, before it enters the roomNo building work. Fitted in stages while in use.No energy use, no moving parts. Cleaned like a window.
External blinds and screensIn front of the glass, most effectiveWork on the facade. Sometimes needs consent or a permit.Motors and servicing. Retracted in strong wind.
Internal blinds and roller blindsBehind the glass, heat is already insideSmallBlock the view. Close to the glass they raise thermal stress risk.
Air conditioningRemoves heat from the room afterwardsUnits and pipeworkElectricity use and regular servicing
Replacing the glazingIn the new glassMajor work, panes replacedHighest cost and longest works

This is a general comparison. We assess the right solution for a specific building at the site visit.

Preparing for the installation

Film is applied wet, so the fitter needs to reach the glass from the front and the sides with a squeegee, knife and sprayer.

We need clear access to the windows – at least 1 metre. Please leave roughly 1 m of free space in front of and beside every window. Wardrobes, beds, desks or plants must be moved away before the film is applied, curtains pulled aside and interior blinds raised. The fitters can then work faster and cleaner, with no risk to your furniture.

Caring for window film

Do not clean the film for the first 30 days. A light haze and small water bubbles are normal. They disappear on their own as the film dries. In winter this takes longer.

Do

  • Plenty of water with a drop of mild detergent (no ammonia)
  • Soft microfibre cloth
  • Rubber squeegee for the remaining water
  • Clean exterior film just as gently as interior film

Don’t

  • Razor blades, scrapers and rough sponges
  • Cleaners with ammonia or grit
  • Stickers, tape and suction cups on the film
  • A pressure washer close to the edges of exterior film

Tip from practice: When you clean the frames, take care of the film edges. Do not lift them with a fingernail or cloth.

Full film care guide

Updated: November 2026

Why choose us to fit your film

We are a certified 3M Endorsed Installer. Our fitters were trained and tested by 3M itself. We have been fitting window and car films for 25 years. How long a film lasts depends on how well it is fitted.

  • We have even worked inside nuclear power plants

    We fitted film at the Jaslovské Bohunice and Mochovce nuclear power plants. With security clearance, work permits and the strictest health and safety rules. We bring the same discipline to your flat or office.

  • Open shopping centres and work from platforms

    Aupark, Eurovea and Polus did not close for us. We worked section by section and before opening. The work area was fenced off. We reached atriums and skylights from platforms. All our installers are certified for work at height and for operating aerial work platforms and walkways.

  • Only premium materials, data shown openly

    We use only premium films from 3M, Avery Dennison, ORAFOL and Solar Screen. They last longer, keep their colour and carry a manufacturer warranty. For every film you get the data sheet and certificates. The values in our quote are the manufacturer’s figures to recognised standards. Not sales promises.

  • We tell you when film isn’t the answer

    Sometimes film will not solve the problem. Or the glass could crack from uneven heat (thermal stress). Then we tell you plainly and suggest what to do instead.

How it works

From your first message to the finished job usually takes a few days. For buildings, we plan the work so it does not disrupt your operations.

  1. Enquiry or photo

    Fill in the online form and see an estimated price at the end. Or send a photo to m2s@m2s.sk. Rough sizes are enough.

  2. Free site visit

    For buildings, we visit, measure the windows and check the glass. Then we recommend a suitable film.

  3. Your quote

    We prepare it as soon as possible. It has a clear price, the exact material, a date and the warranty terms.

  4. Installation and warranty

    Our team of two installers fits the film. You get the data sheet, the manufacturer’s warranty terms and an invoice. For cars, also a certificate of installation.

Frequently asked questions

Didn’t find your answer? E-mail us or send a free quote request – advice costs nothing.

Send us an e-mail
What is the maximum office temperature in summer in Slovakia?

For seated office work, the highest permitted temperature is 28 °C. The optimum is 23 to 27 °C. This is set by Regulation No. 99/2016 for the warm season.

What must an employer do when the office is too hot?

They must take measures against heat stress. The regulation lists, for example, air conditioning, breaks, shifting working hours and shading of windows. Your health and safety adviser will recommend the exact steps.

Does window film count as window shading?

Film stops a large share of solar heat right at the glass. Your health and safety adviser decides how to reflect it in your records. We supply data sheets with the film’s values.

Will film replace air conditioning?

Not completely. Film cuts heat from the sun, but not heat from equipment and people. The air conditioning then runs less and the office is more comfortable.

How many degrees cooler will the office be?

In direct sun, often 2 to 6 °C. It depends on orientation, glass area, ventilation and the film. We calculate the heat saving after a site visit.

Will the office get darker?

With a light film, hardly. 3M Prestige 70 lets through 63 % of light on double glazing. The eye perceives the drop as smaller than the number suggests.

Can film be fitted without disrupting work?

Yes. We work room by room, in the evening or at weekends. The film is fitted wet, with no drilling and no dust.

Is film safe for double and triple glazing?

Yes, if chosen correctly. We assess every pane for thermal stress. For triple glazing and large panes we often choose exterior film.

Will film affect Wi-Fi or mobile signal in the building?

Metal-free films like 3M Prestige don’t block signal. Only films with a metal layer can weaken it. More on window film and mobile signal.

How long does the film last?

Interior films commonly last 10 to 15 years or more. Exterior 3M Prestige lasts 10 to 15 years. We state the manufacturer’s warranty in the quote.

Can you work at height on a facade?

Yes, from platforms and scaffolding. The team is always two fitters certified for work at height. See high-access work.

Will you supply documents for procurement?

Yes. We supply film data sheets with manufacturer values and an invoice. We prepare the quote with an itemised breakdown.

What do I need to prepare before the film is applied?

Clear access to the windows: leave roughly 1 metre of free space in front of and beside every window. Move wardrobes, beds, desks and plants away beforehand, clear the window sills, pull curtains aside and raise interior blinds. If something heavy cannot be moved, tell us in advance and we will plan around it.

Gloved hands stretching blue film over a car body

Send us a photo of your window or car. We’ll prepare a quote as soon as possible.

A few details and a phone photo are enough. We’ll e-mail you a quote as soon as possible.

  1. 1Service
  2. 2Details
  3. 3Photos
  4. 4Price

What do you need?

The more you tell us, the more accurate the quote. You will see an estimated price at the end.

Job type

Which car is it?

The model and scope let us price precisely – we have film patterns for most cars.

Car

Services

Choose any.

Window tinting

Which windows to tint

Front side windows: clear 3M Safety film only. Windscreen: sun strip only. Choose both in the services above. Pick windows on the 3D model

PPF paint protection film

Coverage

Pick exact panels on the 3D car model.

Film

The estimate below is for gloss PPF. We state the price difference between GSWF, Avery Dennison and HOHO in the quote.

Finish

Film type

Tell us about the windows

Approximate details are enough. We measure precisely during the free site visit.

What do you want to solve?

Choose any.

Film type

Price of the film alone, incl. VAT. Application is added.

Glass sizes

How to measure the glass

Film is applied to the glass only, never to the frame. Measure just the visible glass – from bead to bead.

glass width glass height frame don’t measure bead measure from here
  1. Measure the width and height of the visible glass from one glazing bead to the opposite bead. Do not measure the frame or the sash.
  2. Measure each pane separately. If the window has glazing bars, measure each section and enter how many identical pieces there are.
  3. Centimetre accuracy is enough – round up. We cut the film to size on site anyway.
  4. Not sure? Send a photo of the window with a tape measure, or book a free site visit.

Measure the glass only, bead to bead – not the frame. Enter identical panes once with a quantity.

WidthHeightQtyRemove
cm cm
m²
Film applied

Glass and windows

Glass type
Window frame type

With wooden windows the application costs 20 % more.

Window orientation (choose any)
Access to the windows

Where is the job?

We work out travel from Bratislava from the town.

km

Extras

We need clear access to the windows – at least 1 metre. Please leave roughly 1 m of free space in front of and beside every window. Wardrobes, beds, desks or plants must be moved away before the film is applied, curtains pulled aside and interior blinds raised. The fitters can then work faster and cleaner, with no risk to your furniture.

Photos and notes

A phone photo is often enough for an accurate quote without a visit. Photograph the whole window and its surroundings; for cars the full side and front.

Photos

Site visit

Estimated price

–

    This is an estimate based on your details. We confirm the exact price after a visit or from photos – we will get back to you as soon as possible.

    Where should we send the quote?

    Contact

    How should we contact you?

    Company

    Optional. Fill in if the quote is for a company.

    Search