3Mfolie.skWindow & car films
Loft apartment with roof windows

All of Slovakia

Film for roof windows and skylights against overheating

A roof window or skylight brings plenty of light into the attic. In summer, it also brings plenty of heat. Film cuts that heat a lot and keeps your view of the sky. But sloped glass needs different films and a different method from an ordinary window.

  • Exterior films for sloped glazing
  • Films for glass and polycarbonate
  • Certified, safe work at height

In short

For roof windows, skylights and glass roofs we most often recommend exterior solar film. This includes Velux- or Fakro-type windows, for example. Good choices are 3M Prestige Exterior or Avery Dennison SkyLite 20 XTRM PRO, made for horizontal and sloped glass. It stops heat before it reaches the glass. So it puts no thermal stress on the insulating glass (the risk of cracking from uneven heating). Polycarbonate needs films made for plastics. The warranty on sloped glass is shorter than on vertical glass.

Materials we install

What window film does for you

  • Less heat in the room

    Depending on film and glass, it stops 36 to 85 % of solar energy. Homes and offices stay cooler in summer.

  • Less glare

    You can see your screen and TV even in the sun. No need to keep the blinds down all day.

  • UV protection

    The film stops up to 99 % of UV radiation. Floors, furniture and shop-window goods fade much more slowly.

  • No new windows needed

    We apply film to your existing glass. A flat or house usually takes one day, with no dust or building work.

Attic bedroom with roof windows in a sloping ceiling

Why the attic overheats

Sloped glass faces the summer sun head-on. More energy falls on it, and for longer each day. Warm air also collects under the roof. So an attic bedroom is hard to sleep in during summer.

Solar energy is 53 % infrared, which is heat. 44 % is visible light (IWFA). Solar film stops a large part of the heat. The room stays bright but heats up less.

Film outside or inside

For roof windows we most often choose exterior film. They almost always have double or triple glazing, often with a Low-E coating (it reflects heat back into the room). The sun also shines on them longer than on upright windows.

Exterior film stops heat before the glass and works better. It does not expose the insulating glass to thermal stress. See the comparison on interior vs. exterior film.

We consider interior film only for smaller windows with suitable glass. Or when the window cannot be safely reached from outside. Also watch out for interior blinds close to the glass. Heat builds up between them and the glass.

The films we use

  • 3M Prestige Exterior – a non-metallic film that reflects little. Shades range from the light Prestige 90 to the dark Prestige 20. According to the manufacturer, Prestige 40 Exterior rejects 71 % of solar energy on double glazing. Prestige 20 Exterior rejects 76 %.
  • Avery Dennison SkyLite 20 XTRM PRO – an exterior film for demanding horizontal and sloped glass skylights. That is what the manufacturer designed it for. It has a single layer, so the edges usually need no sealing. The exception is where water collects.
  • Avery Dennison SkyLite 20 XTRM PRO Poly – the version for plastic skylights and roofs. It also suits multi-wall sheets. Standard window film does not belong on plastic. More on polycarbonate film.
  • Reflective films, such as 3M Silver 15 Exterior – they stop the most heat. On double glazing it is 85 %, according to the manufacturer. But they let through only 16 % of light and look mirrored outside.
Atrium with a glass roof

Glass roofs and atriums

Glazed roofs act like a greenhouse in summer. This applies to conservatories, pergolas, walkways and atriums.

On glass roofs we apply exterior solar films. We do large areas from platforms or scaffolding.

In conservatories we often put a stronger film on the roof and a lighter one on the walls. That way plants still get enough light. More on conservatory window film and shopping centres.

With polycarbonate roofs we check the surface. Yellowed, scratched or weathered plastic is sometimes better replaced than filmed. We will tell you so openly.

Warranty, sealing and condensation

Sloped and horizontal glass is harder on film. Sun, standing water, snow and dirt all wear it down. So manufacturers give it a shorter warranty.

Look at 3M’s warranty terms for Europe (Central European climate zone). 3M Prestige Exterior has 7 years at a slope of 0° to 74°. On vertical glass it has 10 years. We state the specific warranty in the quote.

We seal the edges where water or snow can collect with neutral-cure silicone. Check the seal at least once a year, especially after winter.

Condensation on roof windows mainly depends on indoor humidity and the glass temperature. Film will not solve it; ventilation helps. If water often forms on the inside of the window, we prefer exterior film.

Worker in the basket of a boom lift

Access and work safety

Many roof windows in family homes can be rotated or tilted. We can then reach the outer glass from inside. If the window does not allow this, we work from the roof with fall protection or from a platform.

We film skylights and glass roofs on buildings from platforms and scaffolding, with fall-arrest equipment. All our installers are certified for work at height and for operating aerial work platforms and walkways. We never step directly onto a glass roof. More about work at height on high-access installation.

Cleaning film on sloped glass

More dirt stays on sloped glass. Rain does not rinse it off as well as on an upright window.

First rinse the exterior film with clean water. Then wash it with a mild solution and a soft cloth. The solution should have a pH of about 6 to 8, with no ammonia or solvents.

Do not use brushes, abrasives (scouring products) or high-pressure water at close range. Avery Dennison recommends cleaning exterior films at least three times a year. Details are in the film cleaning and care guide.

Glazing type → recommended film

Glazing typeRecommended filmNote
Roof window with double or triple glazingExterior 3M Prestige Exterior or Avery Dennison SkyLite 20 XTRM PRO.Interior film only after a glass check.
Glass skylightAvery Dennison SkyLite 20 XTRM PRO, 3M Prestige Exterior.Edge sealing where water collects
Conservatory glass roofExterior solar film, stronger on the roof.Enough light for plants
Atrium, glazed building roofExterior solar or reflective filmPlatform work, also during operation.
Polycarbonate, multi-wall sheetsAvery Dennison SkyLite 20 XTRM PRO PolyYellowed or weathered plastic checked first.
Acrylic, plastic domesOnly a film the maker specifies for plastics.Suitability confirmed when quoting

Film suitability follows 3M and Avery Dennison technical data sheets and bulletins. Performance is based on 3M data (EN 410 / NFRC). The warranty on sloped and horizontal glass is shorter than on vertical glass. We state the specific warranty in the quote.

Preparing for the installation

Film is applied wet, so the fitter needs to reach the glass from the front and the sides with a squeegee, knife and sprayer.

We need clear access to the windows – at least 1 metre. Please leave roughly 1 m of free space in front of and beside every window. Wardrobes, beds, desks or plants must be moved away before the film is applied, curtains pulled aside and interior blinds raised. The fitters can then work faster and cleaner, with no risk to your furniture.

Caring for window film

Do not clean the film for the first 30 days. A light haze and small water bubbles are normal. They disappear on their own as the film dries. In winter this takes longer.

Do

  • Plenty of water with a drop of mild detergent (no ammonia)
  • Soft microfibre cloth
  • Rubber squeegee for the remaining water
  • Clean exterior film just as gently as interior film

Don’t

  • Razor blades, scrapers and rough sponges
  • Cleaners with ammonia or grit
  • Stickers, tape and suction cups on the film
  • A pressure washer close to the edges of exterior film

Tip from practice: When you clean the frames, take care of the film edges. Do not lift them with a fingernail or cloth.

Full film care guide

Updated: November 2026

Why choose us to fit your film

We are a certified 3M Endorsed Installer. Our fitters were trained and tested by 3M itself. We have been fitting window and car films for 25 years. How long a film lasts depends on how well it is fitted.

  • We have even worked inside nuclear power plants

    We fitted film at the Jaslovské Bohunice and Mochovce nuclear power plants. With security clearance, work permits and the strictest health and safety rules. We bring the same discipline to your flat or office.

  • Open shopping centres and work from platforms

    Aupark, Eurovea and Polus did not close for us. We worked section by section and before opening. The work area was fenced off. We reached atriums and skylights from platforms. All our installers are certified for work at height and for operating aerial work platforms and walkways.

  • Only premium materials, data shown openly

    We use only premium films from 3M, Avery Dennison, ORAFOL and Solar Screen. They last longer, keep their colour and carry a manufacturer warranty. For every film you get the data sheet and certificates. The values in our quote are the manufacturer’s figures to recognised standards. Not sales promises.

  • We tell you when film isn’t the answer

    Sometimes film will not solve the problem. Or the glass could crack from uneven heat (thermal stress). Then we tell you plainly and suggest what to do instead.

How it works

From your first message to the finished job usually takes a few days. For buildings, we plan the work so it does not disrupt your operations.

  1. Enquiry or photo

    Fill in the online form and see an estimated price at the end. Or send a photo to m2s@m2s.sk. Rough sizes are enough.

  2. Free site visit

    For buildings, we visit, measure the windows and check the glass. Then we recommend a suitable film.

  3. Your quote

    We prepare it as soon as possible. It has a clear price, the exact material, a date and the warranty terms.

  4. Installation and warranty

    Our team of two installers fits the film. You get the data sheet, the manufacturer’s warranty terms and an invoice. For cars, also a certificate of installation.

Frequently asked questions

Didn’t find your answer? E-mail us or send a free quote request – advice costs nothing.

Send us an e-mail
Can film be applied to a roof window?

Yes. On roof windows (e.g. Velux or Fakro type) we most often apply exterior solar film. It stops heat before the glass and puts no load on the insulating glass.

What is the best heat control film for a roof window?

To keep the light, choose non-metallic 3M Prestige 70 or 50 Exterior. If the attic is very hot, choose Prestige 40 or 20 Exterior. Reflective films stop the most heat. But they look mirrored and darker.

Can the film on a roof window go on the inside?

For smaller windows with suitable glass, yes, but always after an assessment. Roof windows are in the sun for a long time. So interior film raises the risk of thermal stress.

Why is the warranty shorter on roof windows?

Because sloped glass takes more sun, water and snow. In Central Europe, for example, 3M gives Prestige Exterior 7 years on sloped glass. On vertical glass it gives 10 years.

Can film be applied to a polycarbonate skylight?

Yes, but only a film made for plastics. For example, Avery Dennison SkyLite 20 XTRM PRO Poly. More on polycarbonate film.

Will I lose the view of the sky?

No, the film is transparent. Darker films reduce brightness, but the view remains.

Will film help with glare in the attic?

Yes, a darker film reduces glare. For example, 3M Prestige 40 Exterior cuts it by 52 % compared with clear glass, according to the manufacturer.

How is film on roof windows cleaned?

Rinse the exterior film with water first. Then use a mild solution and a soft cloth, with no brushes or abrasives. Check the edge seal once a year, especially after winter.

Do you also do large glass roofs and atriums?

Yes, from platforms and scaffolding, also while the building is in use. See high-access installation and shopping centres. A price example with a platform is in how much window film costs.

Will film replace an external blind on a roof window?

Not fully. A closed external blind usually stops more heat, but it blocks the view and the light. Film works all the time and keeps the window clear. See the comparison on film vs. blinds and air conditioning.

What do I need to prepare before the film is applied?

Clear access to the windows: leave roughly 1 metre of free space in front of and beside every window. Move wardrobes, beds, desks and plants away beforehand, clear the window sills, pull curtains aside and raise interior blinds. If something heavy cannot be moved, tell us in advance and we will plan around it.

Gloved hands stretching blue film over a car body

Send us a photo of your window or car. We’ll prepare a quote as soon as possible.

A few details and a phone photo are enough. We’ll e-mail you a quote as soon as possible.

  1. 1Service
  2. 2Details
  3. 3Photos
  4. 4Price

What do you need?

The more you tell us, the more accurate the quote. You will see an estimated price at the end.

Job type

Which car is it?

The model and scope let us price precisely – we have film patterns for most cars.

Car

Services

Choose any.

Window tinting

Which windows to tint

Front side windows: clear 3M Safety film only. Windscreen: sun strip only. Choose both in the services above. Pick windows on the 3D model

PPF paint protection film

Coverage

Pick exact panels on the 3D car model.

Film

The estimate below is for gloss PPF. We state the price difference between GSWF, Avery Dennison and HOHO in the quote.

Finish

Film type

Tell us about the windows

Approximate details are enough. We measure precisely during the free site visit.

What do you want to solve?

Choose any.

Film type

Price of the film alone, incl. VAT. Application is added.

Glass sizes

How to measure the glass

Film is applied to the glass only, never to the frame. Measure just the visible glass – from bead to bead.

glass width glass height frame don’t measure bead measure from here
  1. Measure the width and height of the visible glass from one glazing bead to the opposite bead. Do not measure the frame or the sash.
  2. Measure each pane separately. If the window has glazing bars, measure each section and enter how many identical pieces there are.
  3. Centimetre accuracy is enough – round up. We cut the film to size on site anyway.
  4. Not sure? Send a photo of the window with a tape measure, or book a free site visit.

Measure the glass only, bead to bead – not the frame. Enter identical panes once with a quantity.

WidthHeightQtyRemove
cm cm
m²
Film applied

Glass and windows

Glass type
Window frame type

With wooden windows the application costs 20 % more.

Window orientation (choose any)
Access to the windows

Where is the job?

We work out travel from Bratislava from the town.

km

Extras

We need clear access to the windows – at least 1 metre. Please leave roughly 1 m of free space in front of and beside every window. Wardrobes, beds, desks or plants must be moved away before the film is applied, curtains pulled aside and interior blinds raised. The fitters can then work faster and cleaner, with no risk to your furniture.

Photos and notes

A phone photo is often enough for an accurate quote without a visit. Photograph the whole window and its surroundings; for cars the full side and front.

Photos

Site visit

Estimated price

–

    This is an estimate based on your details. We confirm the exact price after a visit or from photos – we will get back to you as soon as possible.

    Where should we send the quote?

    Contact

    How should we contact you?

    Company

    Optional. Fill in if the quote is for a company.

    Search